Re: Windshield Profile and Rubber
Posted: Wed Jul 03, 2013 7:43 pm
Thanks for keeping tally. Will do.mdawg4x4 wrote:Count me in for 2. That should finish off the 5 you can get back.
60Patrol
An open forum for all enthusiasts of the classic 60 series Nissan Datsun Patrol to gather and share information and gain knowledge. Members share off-road stories, restoration advice, modification ideas in an atmosphere free of a single controller. The fo
https://www.60patrol.com/forum/
Windshield Profile and Rubber
Page 4 of 6
Re: Windshield Profile and Rubber
Posted: Thu Jul 04, 2013 4:33 am
RiverPatrol wrote:What else could you possibly fill the suitcase with? It's not like you need many clothes, it's summer!Esteban wrote:Due to weight limitations and the fact that I’ll have to pay for the extra bag to bring this stuff with me...yada yada yada
i have a good friend who always buys yard sale clothes for overseas trips, and after wearing them she just gives them to someone who can use them. leaving empty luggage for hauling back all the stuff that she purchases during her trip.
thanks Esteban for hauling the windshield seals back, and mailing them out. now if i just could get my hands on the door seals i would be set.
Re: Windshield Profile and Rubber
Posted: Tue Jul 16, 2013 8:57 pm
I'm back from Ecuador, and brought with me the windshield rubber seal as promised. Got all the stock that the small shop had.
I have material good for 8 windshields. Working with Zed numbers, I will cut each piece at around 157", since adding all the waste is not enough to make a complete one of 146". I think that this could prove convenient to make some trials of the joint compound. No idea what to use for it.
I will prepare the pieces and the packages for the 5 that were requested. In the case of mdawg4x4 I will send the two pieces in one single length. I will be sending PM to each one, Zed, Bosque, Sleepyzzz, and Mdawg4x4 in the next few days.
Pictures of the roll will follow soon.
Thanks,
Esteban
I have material good for 8 windshields. Working with Zed numbers, I will cut each piece at around 157", since adding all the waste is not enough to make a complete one of 146". I think that this could prove convenient to make some trials of the joint compound. No idea what to use for it.
I will prepare the pieces and the packages for the 5 that were requested. In the case of mdawg4x4 I will send the two pieces in one single length. I will be sending PM to each one, Zed, Bosque, Sleepyzzz, and Mdawg4x4 in the next few days.
Pictures of the roll will follow soon.
Thanks,
Esteban
Re: Windshield Profile and Rubber
Posted: Tue Jul 16, 2013 10:37 pm
Welcome back Esteban. 
That bag must have given you a bicep workout, thanks and take a rest!!!
I hope your trip was good......seemed a bit short but all vacations are too short.
That bag must have given you a bicep workout, thanks and take a rest!!!
I hope your trip was good......seemed a bit short but all vacations are too short.
Re: Windshield Profile and Rubber
Posted: Wed Jul 17, 2013 4:59 am
glad to hear you made it back and i hope you had a good visit with your brother. thanks so much for hauling the windshield seals back and mailing them out.
Re: Windshield Profile and Rubber
Posted: Wed Jul 17, 2013 5:10 pm
Sorry I didn't get in on this one, but maybe next time 
Re: Windshield Profile and Rubber
Posted: Wed Jul 17, 2013 6:05 pm
I think I just saw a used one on eBay.Urban60 wrote:Sorry I didn't get in on this one, but maybe next time
Kidding!
Re: Windshield Profile and Rubber
Posted: Wed Jul 17, 2013 6:09 pm
RiverPatrol wrote:I think I just saw a used one on eBay.Urban60 wrote:Sorry I didn't get in on this one, but maybe next time
Kidding!
right after the listing for the ambulance doors.Re: Windshield Profile and Rubber
Posted: Wed Jul 17, 2013 7:10 pm
Did you snag the doors? Re: Windshield Profile and Rubber
Posted: Wed Jul 17, 2013 9:22 pm
bosque wrote:
Yes
